trnfltr1.qry

# trnfltr1.qry
# This is a sample script to draw a right-lateral transform
# fault line symbol (solid) with open half-arrows.
# Modified for legend samples August 2002.
# Modified to declare all variables, October 2005
# Version Dec. 2007
# Requires TNTmips 2007:73 or later.
# Modified to adjust scale based on georeference map units and to
# place displacement symbols only at the center of the lines
numeric red, green, blue;
numeric scale, widthMap, width, arrowLengthMap, arrowSize;
numeric flipSize, angle, headBase, offset;
class RVC_GEOREFERENCE vGeoref;
class SR_COORDREFSYS vectCRS;
###################### Set Parameters ##############################
# Red, green, blue variables define the color of the line
red = 255;			green = 0;			blue = 0;
# This variable defines the denominator of the intended map scale.
# It is used as the basis for defining line width and symbol size
# and spacing.
# Example: for 1:24,000 map scale, Scale = 24000
scale = 24000;
# This variable controls the width of the lines.
# WidthMap is the desired map width in mm, assuming vector
# coordinates are in meters.
widthMap = 0.3;
# These variables control the length of the arrows
# ArrowLengthMap is the desired arrow length in mm, assuming vector 
# coordinates are in meters:
arrowLengthMap = 6;
# Check if vector has geographic coordinates (units of degrees instead of meters) 
# and if so adjust scale factor to draw symbols of appropriate size.
Vect.GetDefaultGeoref(vGeoref);
vectCRS = vGeoref.GetCoordRefSys();
if (vectCRS.IsProjected() <> 1) {
	if (vectCRS.IsLocal() <> 1) {
		scale = scale * 0.000009;
		}
	}
else {	# CRS is projected; check coordinate units to adjust scale
	# get coordinate unit from the first axis of the planar coordinate system
	coordUnit$ = vectCRS.Coordsys.GetAxis(1).Unit.GetSymbol();
	scale = scale * GetUnitConvDist("m", coordUnit$);
	}
# set final dimensions for drawing
if (DrawingLegendView == 1) {		# set dimensions for LegendView based on sample size 
	width = 0.1 * SampleRect.GetHeight();
	arrowSize = 0.7 * SampleRect.GetWidth();
	}
else {		# set dimensions for drawing elements in view
	scale = scale / 1000;	# conversion from meters to millimeters
	width = widthMap * scale;
	arrowSize = arrowLengthMap * scale;
	}
# This variable controls the length of the arrow head
flipSize = 0.4 * arrowSize;
# This variable controls the sweep angle of the arrow in degrees
angle = 30;	 # 30 degree angle
headBase = flipSize * sind(angle);
# This variable controls how far from the base line to draw arrows
offset = 0.2 * arrowSize;
######################## Process ###########################
# Set line color, width, and draw fault line.
LineStyleSetColor(red,green,blue);
LineStyleSetLineWidth(width);
LineStyleDrawLine();
# Draw arrows
LineStyleSetPosition(0.5);		# move to center of line
LineStyleRoll(-(arrowSize * 0.5));
# Draw first half-arrow
LineStyleMoveTo(90, offset);
LineStyleLineTo(0, arrowSize);	# draw arrow shaft forward parallel to line
LineStyleDropAnchor(1);
LineStyleLineTo(180 - angle, flipSize);	# arrow head side
LineStyleLineTo(-90, headBase);				# arrow head base
# draw the other half-arrow
LineStyleMoveToAnchor(1);
LineStyleMoveTo(-90, 2 * offset);	# offset to other side of line
LineStyleLineTo(180, arrowSize);		# draw arrow shaft backward parallel to line
LineStyleLineTo(-angle, flipSize);
LineStyleLineTo(90, headBase);